Відео

This literally just happened to me cutting my grass, my Toro mower was starting up 10:48 and then stalling out, I knew that it was something with the carburetor jet I sprayed it but I totally forgot that there was a small hole on the side. So I’m off to buy the carburetor cleaner and more starting fluid. Thank you so much for showing me that, I really do appreciate your video it was awesome! 💪💪

I really wish videos would just get to the point of instructions

It would be really helpful for me to actually hear the noise so I can try to diagnose mine.

You can bend the copper pipe by closing off one end with masking tape. Fill the pipe with sand packed tight. Seal the open end with masking tape. Now you can bend the pipe. The sand will prevent the pipe from crimping at the bend. It's a very old plumbers trick that works.

I found these finger splints that you can buy on Amazon or whatever and they work good for duck feet and legs cuz you can bend it and cut it to shape. Plus it's padded a little bit!

The ankle os bent so a short oops cle stick wpuld be good to attach to keep straight

And connect the legs with sonething stretchy so it doesnt splay to the side

A piece of leather might work better than slick plastic

Fantastic

John deere spindles have grease fitting

Couple things 1) Amazon says the voltage regulator in your link is no longer available. 2) At the end of your video when testing the charging by putting in the jumper wire, which battery terminal do you touch? I assume negative but I never like to assume.

Another option is to go to the Home Depot (or any other hardware supplier), and purchase a piece of 1/2 inch hard copper tubing, and cut the length needed for the wheel, and then press it in by using a soft brass hammer or a block of wood and hammer. It works extremely well and will last as long as the original bushings.

Great video

Thanks for your help 😊

Ok wish me luck. Thank You

Sir obviously what you demonstrated here is truly exceptional advice and teaching. Thank you! Will be saving video. Let me also thank you for making your video about the facts and for not cluttering it up with horrible music so loud that we couldn’t hear you. So many UA-camrs do that and it ruins the video. Yours is simple and useful and much appreciated. Keep up the great work!

What about replacing the oil. Also, the check valve that is attached to the float in the bowl gets stuck with goo. That can get stuck closed. Is there an additive you can add to the gas that will clean up the insides such as Techron?

I have a two-door 2011 Cadillac CTS coupe and the headlight bulbs work when they want to one day they're on one day they're off. I checked the relays are fine but a friend of mine said to replace the bulbs May fix the issue have anyone had the same problem and if so what did you do to resolve the issue.

Thanks

For a video with 57K views, it is sad and dissapointing that only '11' people managed to post comments or show a sign of Gratitude, C'mon you lazy ass morons, come back and post an overdue thanks to this kind hearted person for conducting these valuable test's, he has done it, so we can steam through, makes 'SENSE' (Sensor) get it ?? 🙂

THANK YOU FOR THE VIDEO

Thank you for the video

Thank you for the video

Thank u for helping me get my pressure washer started!

Im not doing this over and over again This thing isn't even that old. I will get it to run and pawn it. This is insane.

A small engine repair guy taught me this years ago. It does work 99% of the time. I use a tiny wire to clean the jet. The other thing you should do is run your mower dry at the end of mowing season, or anytime the mower will be storage for a while.

I’ve had it happen twice after sitting during the winter. I decided to take the spark plug out and dip the tip in gas and put it back in. It started up right away.

another option is motocraft's keyable ingnition cylinders. they are more expensive than the doorman option, but cheaper than getting keys programed. it's a good option if you want your doors and ignition keyed alike.

Wow, thanks. I think I can do this! 😊

Mine won’t start now 🤦🏾‍♂️

Thanks!

Yo!!! buck help me please 😢... I've put in the main jet, new gas,spark plug,and air filter also new blade it still won't crank???? .. so I'm just floored.... I have the same lawnmower in video a Craftsman self-propelled lawn mower m 260 163 CC.... What am I missing what can I do my brother

Thanks

A lil thing with a point fell out where dies it go back in smh

Great video 👍

Two small things. Should there be a thin coating of grease on the spindle before putting the new wheels back on, and could you use the hubcap that came off the front and put them on the rear where they were lost.

The video is 11mins 47sec???

Thanks Buck! I didn’t even have to take the carburator apart and it worked after 5 years sitting outside! I own a different lawnmower and by just removing the air filter I have direct access to the “bowl” and I shot the cleaner through all the orifices. That small no traction lawnmower was my jogging buddy I used to mow 20,000 feet with it on the regular. It saw a loooot of grass and we are finally reunited thanks to you, your tips worked beautifully!

Good job. Nice presentation!

It was fine all morning. Mowed two lawns then stopped working out of no where. It’s stress but has no power behind it now. The other problem is that once the blades engage, the mower turns off. m430

I would add the appropiate dye (M6X1.00) on the rod before cutting it so as to clean up the rod making it much easier to put the nut on.

Nice, Is that the Mantis model #7924, that they rent out @ HD ?

My dumb ass thought i was supposed to string ONE piece THROUGH on the underside 🫠 appreciate the video! Lol back to work now!

I’ve been doing this for years

Thanks to Bidenomics I will be moving into an RV instead of a home, hence I am looking at how to make a permanent connection that will have to work in Northern Michigan winters. As a disabled veteran who sees how we are treated compared to illegal immigrants, I hope no one in their right minds and taking a beating economically due to this failure of a human being and all his enablers will vote for 4 more years of the destruction of America. FJB!

Great video. I need help. Pull start cord rips out of my hand when i attempt to pull / start it. Does anyone know why and the fix? Its been a year and I'm still at a dead end. Ryobi GCV 190 3100psi 2.5 GPM

thanks worked perfect👌

Thanks for your help,I'm about to tackle it soon!!! I always buy local in case I have an issue. You may want to try Wix filters,they are the best in my book. THNX again!~ 1996 Transport owner of 25 years!

When my deck got like that or worse actually, I swapped it out for a new one, it came with all the pulleys, blades & belt , assembeled. $500.00 but I'm much happier.

Looks sketchy af